Hi Dave. Yes, here is our 2" ball with the 3/4" shank part# 4924. I hope that helps.
Boules et montages d'attache de remorque Montages de boule d'attache de remorque
Montage de boule d’attache de remorque pour le receveur de 1-1/4 po (montée de 5 po, longueur de 10 po, 3 500 livres)
Montage de boule d’attache de remorque pour le receveur de 1-1/4 po (montée de 5 po, longueur de 10 po, 3 500 livres)
Veuillez prendre note
- Ne pas utiliser dans la position de chute.
Description
Description du produit
- Numéro de produit :
- 36065
Montage de boule d'attache de remorque de Classe 2 pour receveur de 1-1/4 po. Montée de 5 po. Ne pas utiliser dans la position de chute.
- S'adapte aux receveurs de 1-1/4 po
- Pour des tiges de boule d'attache de remorque de 3/4 po.
- Poids brut de la remorque de 3 500 lb. Poids du timon de 300 lb.
- Revêtement de poudre noire
Évaluations (0)
Questions et réponses (10)
Questions et réponses (10)
Description du produit
- Numéro de produit :
- 36065
Montage de boule d'attache de remorque de Classe 2 pour receveur de 1-1/4 po. Montée de 5 po. Ne pas utiliser dans la position de chute.
- S'adapte aux receveurs de 1-1/4 po
- Pour des tiges de boule d'attache de remorque de 3/4 po.
- Poids brut de la remorque de 3 500 lb. Poids du timon de 300 lb.
- Revêtement de poudre noire
Questions et réponses (10)
Can I get a class 2 or 1/14 ball mount with a !" hole for the ball? I have had a few issues with 3/4" shank balls and all I have now are 1" shank.
Hello, Kent! Unfortunately, we do not offer any 1-1/4" ball mounts with a 1" hitch ball hole. You can contact your local U-Haul Hitch Center to get a 2" receiver installed. I hope that is helpful!
I have a 2010 Honda Accord Crosstour with a UHaul hitch and 14 height from the ground. Would this item work with my hitch?
Hello, David! Although the ball mount shank may match the hitch receiver diameter, the weight ratings may differ. Your hitch system is only as strong as its lowest-rated component (Hitch, ball mount, ball). I hope that is helpful!
Would this ball mount be appropriate for a 2007 Honda Odyssey? The one I was given from your installer is too low for my trailer. I need a higher rise.
Hi, Robin! This ball mount will work on a 2007 Honda Odyssey equipped with a 1-1/4" receiver hitch. Thanks for asking!
This ball mount has the rise that I need, but I am concerned as to whether it is long enough to clear the bumper on my 2013 Nissan Sentra. Can you tell me what the horizontal measurement is between the center of the mounting pin hole and the inside of the vertical portion of the bar? I need a minimum length of 7" from the center of the mounting pin hole to the inside of the vertical portion of the bar. NOTE: This bar would be used on a U-Haul receiver hitch, which I had installed today at your store in East Madison, Wisconsin. Merci.
Hey, David! The length from the pin hole to the vertical part of the bar is 7,38 inches. I hope that is helpful!
Is hitch receiver 36065, 5 inch rise okay to use on a 2011 Altima 4 door with uhaul hitch part # 24737
Hi, George! The 36065 1-1/4" ball mount will fit into the 24737 1-1/4" receiver. Please note: your hitch system is only as strong as its lowest rated component.. Thank you!
what is the proper drawbar to use with a 2017 ford fusion 2 AWD? 3,5 or 5 inch rise? Is it available in store?.
Hi, Tom! Please visit your local U-Haul Hitch Center for a free tow inspection and to ensure proper ball mount weight capacity and height selection for your trailer.
You can also visit our How to Select the Correct Ball Mount for your Hitch guide for more information. Thank you!
what is the proper drawbar to use with a 2012 ford fusion se? 3,5 or 5 inch rise.
Hi, Greg! U-Haul ball mount part number 3594 matches your needs (Class l, 1-1/4", 2000 lbs, w/ 3/4" ball hole, 10" Length x 4" rise). Please visit your nearest U-Haul Hitch Location for purchase. Thank you!
Is the 5 inch riser for 1-1/4 inch hitch available in store?
Hi, Rob! This specific ball mount is not available in store. Please contact your local U-Haul Hitch Center to see what they have in stock for your vehicle.
Will a ball hitch work with a 2017 Audi Allroad station wagon? If so is one type better for the car's construction than another?
Currently there are no aftermarket hitch products available for your vehicle. We can expect to see more information by February of 2017. If you are in need of a hitch before then, please visit this page and enter your vehicle information for a possible free custom built hitch.
Articles recommandés
-
Clavette et goupille - classes I et II
$2,95
SANS FRAIS si pris en magasin
Livraison le lendemain
-
Verrou pour receveur à deux clavettes recourbées
$17,95
SANS FRAIS si pris en magasin
Livraison le lendemain
-
Porte-vélos Reese Q-Slot pour 2 vélos
$159,95
Prise en charge en magasin seulement
Livraison le lendemain
Could a 2" hitch ball with 3/4" shank and a 1" rise be used with this ball mount?
Hi Dave. Yes, here is our 2" ball with the 3/4" shank part# 4924. I hope that helps.
Can I get a class 2 or 1/14 ball mount with a !" hole for the ball? I have had a few issues with 3/4" shank balls and all I have now are 1" shank.
Hello, Kent! Unfortunately, we do not offer any 1-1/4" ball mounts with a 1" hitch ball hole. You can contact your local U-Haul Hitch Center to get a 2" receiver installed. I hope that is helpful!
I have a 2010 Honda Accord Crosstour with a UHaul hitch and 14 height from the ground. Would this item work with my hitch?
Hello, David! Although the ball mount shank may match the hitch receiver diameter, the weight ratings may differ. Your hitch system is only as strong as its lowest-rated component (Hitch, ball mount, ball). I hope that is helpful!
Would this ball mount be appropriate for a 2007 Honda Odyssey? The one I was given from your installer is too low for my trailer. I need a higher rise.
Hi, Robin! This ball mount will work on a 2007 Honda Odyssey equipped with a 1-1/4" receiver hitch. Thanks for asking!
This ball mount has the rise that I need, but I am concerned as to whether it is long enough to clear the bumper on my 2013 Nissan Sentra. Can you tell me what the horizontal measurement is between the center of the mounting pin hole and the inside of the vertical portion of the bar? I need a minimum length of 7" from the center of the mounting pin hole to the inside of the vertical portion of the bar. NOTE: This bar would be used on a U-Haul receiver hitch, which I had installed today at your store in East Madison, Wisconsin. Merci.
Hey, David! The length from the pin hole to the vertical part of the bar is 7,38 inches. I hope that is helpful!
Is hitch receiver 36065, 5 inch rise okay to use on a 2011 Altima 4 door with uhaul hitch part # 24737
Hi, George! The 36065 1-1/4" ball mount will fit into the 24737 1-1/4" receiver. Please note: your hitch system is only as strong as its lowest rated component.. Thank you!
what is the proper drawbar to use with a 2017 ford fusion 2 AWD? 3,5 or 5 inch rise? Is it available in store?.
Hi, Tom! Please visit your local U-Haul Hitch Center for a free tow inspection and to ensure proper ball mount weight capacity and height selection for your trailer.
You can also visit our How to Select the Correct Ball Mount for your Hitch guide for more information. Thank you!
what is the proper drawbar to use with a 2012 ford fusion se? 3,5 or 5 inch rise.
Hi, Greg! U-Haul ball mount part number 3594 matches your needs (Class l, 1-1/4", 2000 lbs, w/ 3/4" ball hole, 10" Length x 4" rise). Please visit your nearest U-Haul Hitch Location for purchase. Thank you!
Is the 5 inch riser for 1-1/4 inch hitch available in store?
Hi, Rob! This specific ball mount is not available in store. Please contact your local U-Haul Hitch Center to see what they have in stock for your vehicle.
Will a ball hitch work with a 2017 Audi Allroad station wagon? If so is one type better for the car's construction than another?
Currently there are no aftermarket hitch products available for your vehicle. We can expect to see more information by February of 2017. If you are in need of a hitch before then, please visit this page and enter your vehicle information for a possible free custom built hitch.